|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Preliminary 8 Typical Applications * TDMA-GSM Cellular/PCS Handsets * TDMA Cellular/PCS Handsets * GAIT Handsets RF2492 DUAL-BAND LOW NOISE AMPLIFIER/MIXER * CDMA Cellular/PCS Handsets * GSM DCS/PCS Handsets Product Description The RF2492 is a fully featured dual-band LNA/Mixer and is usable in a variety of mobile handset applications. The unique dual IF outputs provide interface to two independent IF SAW filters supporting applications such as TDMA-EDGE where 30kHz and 200kHz bandwidth SAW filters are used. With independent power management control pins for the LNAs and mixers, either IF output can be accessed from either high- or low-band LNAs, providing maximum flexibility with minimum power usage. Multiple gain control options are provided to achieve a very large dynamic range for the receiver. A frequency doubler is included in the LO circuit to generate both high- and low-band LO signals with a single VCO. The RF2492 is packaged in a 32 pin, 5mmx5mm, leadless plastic package. Optimum Technology Matching(R) Applied Si BJT Si Bi-CMOS GaAs HBT GaAs MESFET Si CMOS 1.00 0.85 0.80 0.65 0.60 0.24 typ 5.00 sq. 0.45 0.20 4 PLCS 3 0.30 0.18 3.25 2.95 sq. 12 MAX 0.05 0.01 0.55 0.30 0.50 NOTES: 1 Shaded Pin is Lead 1. 0.23 0.13 4 PLCS 8 FRONT-ENDS 2 Pin 1 identifier must exist on top surface of package by identification mark or feature on the package body. Exact shape and size is optional. 3 Dimension applies to plated terminal: to be measured between 0.02 mm and 0.25 mm from terminal end. 4 Package Warpage: 0.05 mm max. 5 Die Thickness Allowable: 0.305 mm max. Package Style: LCC, 32-Pin, 5x5 PCS LNA OUT uSiGe HBT PCS MIX IN 25 23 Features * Complete Dual-Band Receiver Front End * Low Noise Figure 4 5 PCS LNA IN 30 7 LNA GAIN SEL 12 MIX GAIN SEL 14 8 IF1+ IF1IF2IF2+ * Stepped LNA/Mixer Gain Control * Adjustable LNA Bias Current/IIP3 * Integrated LO Frequency Doubler * Differential LO Buffer Outputs CELL LNA IN 11 IF SEL 9 LNA IP SEL 10 LNA ISET 17 BAND SEL 31 X2 ENABLE 32 15 18 1 LOGIC CONTROL X2 19 PCS LO OUT+ 20 PCS LO OUT 21 CELL LO OUT+ 22 CELL LO OUT- Ordering Information RF2492 RF2492 PCBA Dual-Band Low Noise Amplifier/Mixer Fully Assembled Evaluation Board CELL LNA OUT CELL MIX IN LO IN Functional Block Diagram RF Micro Devices, Inc. 7625 Thorndike Road Greensboro, NC 27409, USA Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com Rev A4 010828 8-33 RF2492 Absolute Maximum Ratings Parameter Supply Voltage Input LO and RF Levels Operating Ambient Temperature Storage Temperature Preliminary Rating -0.5 to +5.0 +6 -40 to +85 -40 to +150 Unit VDC dBm C C Caution! ESD sensitive device. RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s). Parameter Overall RF Frequency Range Specification Min. Typ. Max. 881 1960 800 1700 950 2100 110 50 -13.0 -14.0 250 -12.7 -12.7 Unit MHz MHz MHz MHz MHz MHz dBm dBm Condition T = 25C, VCC =2.75V Specifications Specifications Usable range Usable range Specifications Usable range T1 insertion loss not considered. T2 insertion loss not considered. Freq=869MHz to 894MHz RF=880MHz and 881MHz LNA set for max IIP3 LNA set for Nominal IIP3 LNA set for max IIP3 LNA set for Nominal IIP3 LNA set for max IIP3 LNA set for Nominal IIP3 IF Frequency Range Cell LO Buffer Output PCS LO Buffer Output Cellular Band LNA (On) Gain 8 FRONT-ENDS 13.5 13.5 Noise Figure Input IP3 +7.0 +1.5 -8.5 5.5 +20.0 14.5 14 2.0 1.8 +7.5 +3.0 -7.5 5.8 +21.0 15.5 15 2.2 2.0 +7.0 -6.5 6.0 dB dB dB dB dBm dBm dB dB dBm LNA (Off) Gain Noise Figure Input IP3 Mixer Gain 12 3.5 6.5 13.5 +2.0 +11.5 -10 13 4.4 7.0 14.0 +4.5 +13.8 -5 14 5.0 7.5 14.5 dB dB dB dB dBm dBm dBm dBm Noise Figure Input IP3 LO Input Level +3 Mixer Gain 12 3.0 6.8 13.7 +2.0 +11.5 -10 13 4.4 7.2 14.0 +4.5 +14.0 -5 14 dB dB dB dB dBm dBm dBm dBm Noise Figure Input IP3 LO Input Level 7.4 14.2 +3 IF Select=1, (IF1) RF=880MHz, LO=990MHz@-5dBm Mixer RF amp ON; ZLOAD =1k single-ended Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Specifications Usable range IF Select=0, (IF2) RF=880MHz, LO=990MHz@-5dBm Mixer RF amp ON; ZLOAD =1k single-ended Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Specifications Usable range 8-34 Rev A4 010828 Preliminary Parameter Mixer Isolation LO to RF LO to RF RF to LO RF to LO LO to IF1 LO to IF2 IF1 to RF RF to IF1 IF2 to RF RF to IF2 40 33.5 56.5 54.5 24 28 50 43.5 49.5 43 42 35 63 60.5 36.5 42 51 44.5 50.5 45 24.5 24 15.9 15.4 2.8 2.7 5.3 5.4 -6.5 -6.4 +1.1 0 2.5 -6.0 17.4 24.5 +14.5 +19.0 dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBm dB dB dB dB dBm dBm RF2492 Specification Min. Typ. Max. Unit Condition Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON IF Select=1, 3dB RF Filter Insertion Loss LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF IF Select=1, 3dB RF Filter Insertion Loss Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Freq=1930MHz to 1990MHz RF=1960MHz and 1961MHz LNA set for max IIP3 LNA set for Nominal IIP3 LNA set for max IIP3 LNA set for Nominal IIP3 LNA set for max IIP3 LNA set for Nominal IIP3 Cascade (LNA On) Gain Noise Figure Input IP3 8 FRONT-ENDS Cascade (LNA Off) Gain Noise Figure Input IP3 PCS Band LNA (On) Gain Noise Figure Input IP3 1.7 +7.0 +0.5 -7.0 6.0 +20.0 13.0 13.0 14.8 14.0 1.5 1.8 +9.0 +3.5 -5.5 6.2 +25.0 dB dB dB dB dBm dBm dB dB dBm 1.9 1.9 LNA (Off) Gain Noise Figure Input IP3 6.5 Mixer Gain 11.5 2.0 8.0 15.0 +4.0 +14.0 -10 12.5 3.5 8.5 15.5 +6.0 +16.0 -5 dB dB dB dB dBm dBm dBm dBm Noise Figure Input IP3 LO Input Level 9.0 16.0 +3 RF=1960MHz, LO=1035MHz@ -5dBm, IF Select=1 (IF1) Mixer RF amp ON; ZLOAD =1k single-ended Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Specifications Usable range Rev A4 010828 8-35 RF2492 Parameter Mixer Gain 11.0 2.0 8.0 15.0 +3.5 +14.0 -10 12.6 3.5 8.4 15.5 +6.0 +16.0 -5 dB dB dB dB dBm dBm dBm dBm dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBm dB dB dB dB dBm dBm V V mA mA mA mA mA mA mA mA Preliminary Specification Min. Typ. Max. Unit Condition RF=1960MHz, LO =1035MHz@-5dBm, IF Select=0 (IF2) Mixer RF amp ON; ZLOAD =1k single-ended Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Specifications Usable range Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON Mixer RF amp ON 3dB RF Filter Insertion Loss LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF LNA set for max IIP3; Mixer RF amp ON LNA set for Nominal IIP3; Mixer RF amp ON LNA set for max IIP3; Mixer RF amp OFF LNA set for Nominal IIP3; Mixer RF ampOFF 3dB RF Filter Insertion Loss Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF Mixer RF amp ON Mixer RF amp OFF IF Select=1 Specifications Operating range Cellular; LNA On, Max IIP3,MixerRFampON Cellular;LNAOn,NomIIP3,Mixer RFamp ON Cellular; LNA Off, Mixer RF amp ON Cellular; LNA Off, Mixer RF amp OFF PCS; LNA On, Max IIP3, Mixer RF amp ON PCS; LNA On, Nom IIP3, Mixer RF amp ON PCS; LNA Off, Mixer RF amp ON PCS; LNA Off, Mixer RF amp OFF Noise Figure Input IP3 LO Input Level 9.0 16.5 +3 57.5 63 52.5 55.5 55.5 59 51 34.5 50.5 42.5 24.3 23.5 15.3 14.5 2.6 3.1 5.7 6.3 -6 -5.6 +3.0 +1.5 4 -5 17 24 +14.0 +21.7 2.75 Mixer Isolation LO to RF LO to RF RF to LO RF to LO LO to IF1 LO to IF2 IF1 to RF RF to IF1 IF2 to RF RF to IF2 55 54 49.8 52 54.5 58.5 49.5 33 49 41 8 FRONT-ENDS Cascade (LNA On) Gain Noise Figure Input IP3 Cascade (LNA Off) Gain Noise Figure Input IP3 Power Supply Supply Voltage 2.7 Supply Current 38 36 32 26 40.0 38.5 34.5 28.0 3.6 40 38 34 28 42.5 40.5 36.0 29.5 LNA Current 8-36 Rev A4 010828 Preliminary State Table (Typical Values for VCC =2.75V and 3dB RF Filter Insertion Loss) RF2492 Cellular PCS Parameter LNA On LNA Off LNA On LNA Off LNA at Max IIP3 LNA at Nom IIP3 LNA at Max IIP3 LNA at Nom IIP3 Mixer Mixer Mixer Mixer Mixer Mixer Mixer Mixer Mixer Mixer Mixer Mixer Amp On Amp Off Amp On Amp Off Amp On Amp Off Amp On Amp Off Amp On Amp Off Amp On Amp Off 24.5 2.8 -6.5 38 14.5 2.0 +7.5 15.9 5.3 +1.1 24 2.7 -6.4 36 14 1.8 +3 15.4 5.4 0 2 18.2 +14.9 32 -7.5 5.8 +21 -6.8 25.2 +19.5 26 -7.5 5.8 +21 24.3 2.6 -6 40 14.8 1.5 +9 15.3 5.7 +3 23.5 3.1 -5.6 38.5 14 1.8 +3.5 14.5 6.3 +1.5 4 17 +14 34.5 -5.5 6.2 25 -5 24 +21.7 28 -5.5 6.2 25 Cascade Gain (dB) Noise Figure (dB) Input IP3 (dBm) Total Current LNA Gain (dB) Noise Figure (dB) Input IP3 (dBm) Isolation (dB) LNA Current (mA) 14.5 2.0 +7.5 14 1.8 +3 14.8 1.5 +9 14 1.8 +3.5 Mixer Gain (dB) Noise Figure (dB) Input IP3 (dBm) LO Input Level (dBm) LO to RF Isolation(dB) Mixer Current (mA) 13 7 +5.1 -5 4.4 14 +13.8 -5 13 7 +5.1 -5 4.4 14 +13.8 -5 13 7 +5.1 -5 4.4 14 +13.8 -5 12.5 8.5 +6 -5 3.5 15.5 +16 -5 12.5 8.5 +6 -5 3.5 15.5 +16 -5 12.5 8.5 +6 -5 3.5 15.5 +16 -5 8 BAND SEL IF SEL 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 X 1 Control Logic Table LNA GAIN 1 1 1 0 0 1 1 1 0 0 1 1 1 0 0 X X MIX GAIN 1 1 0 1 0 1 1 0 1 0 1 1 0 1 0 X X LNA IP SEL 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 X X ENABLE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 PCS IF2 High Gain/High Linearity PCS IF2 High Gain/Nominal Linearity PCS IF2 Mid1 Gain PCS IF2 Mid2 Gain PCS IF2 Low Gain Cell IF2 High Gain/ High Linearity Cell IF2 High Gain/Nominal Linearity Cell IF2 Mid1 Gain Cell IF2 Mid2 Gain Cell IF2 Low Gain Cell IF1 High Gain/ High Linearity Cell IF1 High Gain/ Nominal Linearity Cell IF1 Mid1 Gain Cell IF1 Mid2 Gain Cell IF1 Low Gain Shutdown Not Defined 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 X 1 Rev A4 010828 8-37 FRONT-ENDS RF2492 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Function LO IN VCC2 GND IF1+ IF1BYPASS IF2IF2+ IF SEL LNA IP SEL CELL LNA IN LNA GAIN SEL VCC1 MIX GAIN SEL CELL LNA OUT GND LNA ISET CELL MIX IN PCS LO OUT+ PCS LO OUTCELL LO OUT+ CELL LO OUTPCS MIX IN GND Description LO input for both bands. Impedance is approximately (120-j25). Preliminary Interface Schematic 1k shunt resistor (static bleed). AC coupled to transistor base (internal DC block). Power supply connection for internal LO amplifiers. External low-inductance bypass capacitor between 1nF and 47nF recommended. Ground connection. High-band IF output. Open collector. "Current combiner" IF interface to 1000 SAW filter recommended High-band IF output. Open collector. "Current combiner" IF interface to 1000 SAW filter recommended Pin requires external bypass capacitor between 1nF and 47nF. Low-band IF output. Open collector. "Current combiner" IF interface to 1000 SAW filter recommended Low-band IF output. Open collector. "Current combiner" IF interface to 1000 SAW filter recommended Logic input. High selects IF1 mixer; low selects IF2 mixer. Logic input. High selects external LNA current reference (pin 17); low selects internal LNA current reference. Low-band LNA input (base). Simple external matching required for best performance. Logic input. High selects maximum LNA gain; low selects minimum LNA gain. Power supply for internal references, logic, and mixer preamplifiers. Internal RF bypass capacitor. External bypass capacitor between 1nF and 47nF required. Logic input. High selects maximum mixer gain (mixer RF amp on); low selects minimum mixer gain (mixer RF amp off). Low-band LNA output (collector). Simple external L-C matching required. Ground connection. See evaluation board layout. External current reference for LNA. Resistor to ground sets LNA current when Pin 10 is high. 20k results in approximately 10mA LNA current. Higher resistance results in lower current. Low band mixer RF preamplifier input (base). External L-C network required for best performance. High-band buffered LO output. High-band buffered LO output. Low-band buffered LO output. Low-band buffered LO output. High-band mixer RF preamplifier input (base). External L-C network required for best performance. Ground connection. Keep traces physically short and connect immediately to ground plane (low-inductance ground required for best performance). Internal DC blocking capacitor. 1k shunt resistor (static bleed). Internal DC blocking capacitor. 1k shunt resistor (static bleed). Internal DC blocking capacitor. 1k shunt resistor (static bleed). Internal DC blocking capacitor. 1k shunt resistor (static bleed). Diode to VCC and Ground. CMOS logic interface. 2pF internal shunt capacitance. 2pF internal shunt capacitance. 2pF internal shunt capacitance. 2pF internal shunt capacitance. Diode to VCC and Ground. CMOS logic interface. Diode to VCC and Ground. CMOS logic interface. 8 FRONT-ENDS 13 14 15 16 17 18 19 20 21 22 23 24 Diode to VCC and Ground. CMOS logic interface. 8-38 Rev A4 010828 Preliminary Pin 25 26 27 28 29 30 31 32 Die Flag Function PCS LNA OUT VCC2 GND2 GND2 GND2 PCS LNA IN BAND SEL X2 ENABLE GND Description High-band LNA output (collector). Small external inductance required for best impedance match to 50. High-band LNA power supply connection. Small series inductance required. High-band LNA emitter. Low-inductance ground required. Same as pin 27. Same as pin 27. High-band LNA input (base). Simple external matching required for best performance. Logic input. High selects high-band operation; low selects low-band operation. Logic input. High enables LO doubler; low disables LO doubler. Low inductance ground connection critical to proper operation. RF2492 Interface Schematic Diode to VCC and Ground. CMOS logic interface. Diode to VCC and Ground. CMOS logic interface. 8 FRONT-ENDS Rev A4 010828 8-39 RF2492 Pin Out PCS LNA OUT PCS LNA IN X2 ENABLE BAND SEL Preliminary GND2 GND2 GND2 32 LO IN 1 31 30 29 28 27 26 VCC2 25 24 GND VCC2 2 23 PCS MIX IN GND 3 22 CELL LO OUT- IF1+ 4 21 CELL LO OUT+ IF1- 5 20 PCS OUT- BYPASS 6 19 PCS LO OUT+ IF2- 7 18 CELL MIX IN 8 FRONT-ENDS IF2+ 8 9 IF SEL 10 LNA IP SEL 11 CELL LNA IN 12 LNA GAIN SEL 13 VCC1 14 MIX GAIN SEL 15 CELL LNA OUT 16 GND 17 LNA ISET 8-40 Rev A4 010828 Preliminary Application Schematic BAND SEL RF2492 LNA H IN 120 LO IN X2 ENABLE 33 nF C2 47 nH 33 nF 36 nH 2.2 nH C1 F1 5 OUT VCC 3 GND GND 2 IN 1 VCC 33 pF 1 24 47 nH 4 32 31 30 29 28 27 26 25 33 nF GND GND 6 C1 VCC 18 pF 2 23 3 270 nH IF1 OUT 8 pF 180 nH 5 20 pF 4 22 VCO L OUT N 21 VCO L OUT P 20 VCO H OUT N 33 nF 6 19 VCO H OUT P VCC 7 18 270 nH IF2 OUT 8 pF 180 nH 20 pF 8 9 10 11 12 13 14 15 16 17 47 nH C1 18 pF 27 k 33 nF 3 GND GND 6 GND GND 33 nF 4 pF 2 IN 5 OUT 7.5 nH C2 33 nF VCC 5.6 nH VCC 4 pF 1 4 F2 8 FRONT-ENDS IF SEL IP SET LNA L IN LNA GAIN MIX GAIN LNA L OUT NOTES: 1. C1's are not needed if filter DC impedance is open circuit (as is normally the case). 2. C2's are not needed if duplexer DC impedance is open circuit (as is normally the case). 3. IF interface shown is 50 @ 110 MHz. Rev A4 010828 8-41 RF2492 Evaluation Board Schematic IF=110MHz (Download Bill of Materials from www.rfmd.com.) C28 33 nF R1 120 X2 ENABLE C27 33 nF C26 33 nF L13 47 nH L12 C25 33 nF 36 nH L11 2.2 nH C24 DNI C23 33 nF 3 BAND SEL Preliminary J1 LO IN 636.6 pS Delay 0.20 dB Line Loss 633.0 pS Delay 0.45 dB Line Loss J11 LNA H IN VCC J10 LNA H OUT 637.6 pS Delay 0.45 dB Line Loss F1 5 OUT GND GND 2 32 1 31 30 29 28 27 26 25 24 C22 33 nF L8 47 nH IN 1 GND GND 4 C21 DNI 6 C20 33 nF VCC VCC 460.0 pS Delay 0.02 dB Line Loss R3 DNI C2 8 pF L2 270 nH R2 0 L1 180 nH C3 20 pF C1 18 pF 2 23 6 5 4 IN GND T1 GND 3 2 OUT 605.0 pS Delay 0.40 dB Line Loss J9 MIX H IN 3 22 J2 IF1 OUT 4 21 IN GND 1 421.3 pS Delay 0.11 dB Line Loss J8 LO L OUT 5 20 4 5 IN GND C4 33 nF T2 IN 6 19 3 2 1 442.2 pS Delay 0.28 dB Line Loss C19 33 nF C18 DNI 644.7 pS Delay 0.17 dB Line Loss J7 LO H OUT J6 MIX L IN GND 7 VCC L4 270 nH L3 180 nH 18 6 GND IN 8 FRONT-ENDS J3 IF2 OUT 522.7 pS Delay 0.03 dB Line Loss R5 DNI C6 8 pF R4 0 C5 20 pF 8 9 10 11 12 13 14 15 16 17 L7 47 nH R6 27 k C17 33 nF X2 ENABLE C7 18 pF MIX GAIN C8 33 nF C9 33 nF L5 7.5 nH C10 33 nF C11 33 nF C12 33 nF J4 LNA L IN IF SEL IP SET 629.8 pS Delay 0.17 dB Line Loss LNA GAIN VCC MIX GAIN C13 33 nF C14 33 nF L6 5.6 nH BAND SEL LNA GAIN 3 GND GND 6 GND GND IP SET IF SEL GND GND VCC NC 2 IN 5 OUT P1 P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 10 CON10 C15 4 pF 1 2 3 4 5 6 7 8 9 C16 DNI J5 LNA L OUT 1 4 F2 P1-8 + C29 1 uF VCC 592.7 pS Delay 0.15 dB Line Loss NOTE: T1 and T2 approximate insertion loss is ~2 dB. 8-42 Rev A4 010828 Preliminary Evaluation Board Layout Board Size 3.0" x 3.0" Board Thickness 0.0616", Board Material FR-4, Multi-Layer Assembly RF2492 8 FRONT-ENDS Rev A4 010828 8-43 RF2492 Top Preliminary 8 FRONT-ENDS Typical Inner Layer 8-44 Rev A4 010828 Preliminary Back RF2492 8 FRONT-ENDS Rev A4 010828 8-45 RF2492 20.0 Preliminary Resistor (R6) versus ICC (mA) LNA Low Band Only (LNA High Gain) 3.0 100.0 90.0 LNA Low Band Gain, Noise Figure and IIP3 versus ICC LNA Only (LNA High Gain) 15.0 2.5 80.0 Gain (dB) and IIP3 (dBm) 70.0 Noise Figure (dB) 10.0 2.0 60.0 5.0 1.5 R6 (k) 50.0 40.0 30.0 20.0 0.0 1.0 -5.0 Gain (dB) IIP3 (dBm) NF (dB) 0.5 10.0 0.0 12.0 0.0 2.00 -10.0 2.0 4.0 6.0 8.0 10.0 4.00 6.00 8.00 10.00 12.00 ICC (mA) ICC (mA) 20.00 LNA High Band Gain, Noise Figure and IIP3 versus ICC LNA Only (LNA High Gain) 1.65 100.0 90.0 Resistor (R6) versus ICC (mA) LNA High Band Only (LNA High Gain) 15.00 1.60 80.0 Gain (dB) and IIP3 (dBm) 8 FRONT-ENDS 1.55 70.0 Noise Figure (dB) 10.00 1.50 5.00 1.45 0.00 1.40 Gain (dB) IIP3 (dBm) NF (dB) -10.00 2.00 4.00 6.00 8.00 10.00 1.30 12.00 1.35 60.0 R6 (k) 50.0 40.0 30.0 20.0 10.0 0.0 2.0 4.0 6.0 8.0 10.0 12.0 -5.00 ICC (mA) ICC (mA) 8-46 Rev A4 010828 Preliminary LNA Cellular Band (Low Gain Mode) -7.4 -7.5 21.0 -7.6 20.0 -7.7 22.0 RF2492 LNA Cellular Band (Low Gain Mode) IIP3 (dBm) Gain (dB) -7.8 -7.9 -8.0 19.0 18.0 17.0 -8.1 -8.2 -8.3 2.7 2.8 2.9 3.0 3.1 3.2 3.3 Gain, -30 Gain, 25 Gain, 85 16.0 IIP3, -30 IIP3, 25 IIP3, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 15.0 VCC (V) VCC (V) LNA Cellular Band (High Gain/Nominal IP Mode) 14.4 14.3 14.2 5.0 14.1 6.0 LNA Cellular Band (High Gain/Nominal IP Mode) 5.5 8 FRONT-ENDS IIP3, -30 IIP3, 25 IIP3, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 IIP3 (dBm) Gain, -30 Gain, 25 Gain, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 Gain (dB) 14.0 13.9 13.8 13.7 4.5 4.0 3.5 3.0 13.6 13.5 13.4 2.5 2.0 VCC (V) VCC (V) LNA Cellular Band (High Gain/Nominal IP Mode) 2.4 14.9 14.8 2.2 14.7 2.0 14.6 1.8 LNA Cellular Band (High Gain/Max IP Mode) Noise Figure (dB) Gain (dB) 14.5 14.4 Gain, -30 14.3 Gain, 25 Gain, 85 1.6 1.4 14.2 1.2 NF, -30 NF, 25 NF, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 14.1 14.0 2.7 2.8 2.9 3.0 3.1 1.0 3.2 3.3 VCC (V) VCC (V) Rev A4 010828 8-47 RF2492 LNA Cellular Band (High Gain/Max IP Mode) 8.5 2.6 Preliminary LNA Cellular Band (High Gain/Max IP Mode) 2.4 8.0 2.2 Noise Figure (dB) IIP3 (dBm) 7.5 2.0 1.8 7.0 1.6 1.4 6.5 IIP3, -30 IIP3, 25 IIP3, 85 6.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 1.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 NF, -30 1.2 NF, 25 NF, 85 VCC (V) VCC (V) LNA Cellular Band (High Gain/Nominal IP Mode) 4.50 4.45 6.40 6.35 6.30 6.25 LNA Cellular Band (High Gain /Max IP Mode) 8 FRONT-ENDS ICC (mA) 4.40 4.35 4.30 ICC (mA) 6.20 6.15 6.10 4.25 4.20 4.15 4.10 4.05 4.00 2.70 Icc, -30 Icc, 25 Icc, 85 2.80 2.90 3.00 3.10 3.20 3.30 6.05 6.00 5.95 2.70 Icc, -30 Icc, 25 Icc, 85 2.80 2.90 3.00 3.10 3.20 3.30 VCC (V) VCC (V) 8-48 Rev A4 010828 Preliminary Cellular Band, Mixer IF1, Low Gain Mode, LO @ -5 dBm 5.80 5.60 16.00 5.40 15.50 5.20 16.50 RF2492 Cellular Band, Mixer IF1, Low Gain Mode, LO @ -5 dBm IIP3 (dBm) Gain, -30 Gain, 25 Gain, 85 Gain (dB) 5.00 4.80 4.60 4.40 4.20 4.00 2.75 15.00 14.50 14.00 IIP3, -30 IIP3, 25 IIP3, 85 13.50 2.85 2.95 3.05 3.15 3.25 3.35 13.00 2.75 2.85 2.95 3.05 3.15 3.25 3.35 VCC (V) VCC (V) Cellular Band, Mixer IF1, Low Gain Mode, LO @ -5 dBm 14.00 15.00 Cellular Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 13.50 14.50 13.00 8 FRONT-ENDS 3.35 3.35 Noise Figure (dB) 12.50 12.00 Gain (dB) 14.00 11.50 13.50 Gain, -30 Gain, 25 Gain, 85 NF, -30 NF, 25 NF, 85 13.00 11.00 10.50 10.00 2.75 2.80 2.85 2.90 2.95 3.00 12.50 2.75 2.85 2.95 3.05 3.15 3.25 VCC (V) VCC (V) Cellular Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 9.00 8.00 Cellular Band, Mixer IF1, High Gain Mode, LO @ -5 dBm NF, -30 NF, 25 NF, 85 8.50 8.00 7.50 7.50 7.00 Noise Figure (dB) IIP3, -30 IIP3, 25 IIP3, 85 2.85 2.95 3.05 3.15 3.25 3.35 IIP3 (dBm) 7.00 6.50 6.00 6.50 5.50 5.00 2.75 6.00 2.75 2.85 2.95 3.05 3.15 3.25 VCC (V) VCC (V) Rev A4 010828 8-49 RF2492 Cellular Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 63.00 15.0 Preliminary Cellular Band, Mixer IF1, High Gain Mode, VCC @ 2.75 V 62.00 14.5 61.00 LO to IF Isolation (dB) 14.0 60.00 59.00 Gain (dBm) 13.5 58.00 13.0 57.00 Isolation, -30 56.00 Isolation, 25 Isolation, 85 55.00 2.75 12.0 -10.0 12.5 Gain, -30 Gain, 25 Gain, 85 2.85 2.95 3.05 3.15 3.25 3.35 -8.0 -6.0 -4.0 -2.0 0.0 VCC (V) LO (dBm) Cellular Band, Mixer IF1, High Gain Mode, 5.7 IIP3, -30 IIP3, 25 IIP3, 85 Cellular Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 35.0 VCC = 2.75 V 5.6 34.5 8 FRONT-ENDS IIP3 (dBm) 34.0 5.5 33.5 ICC (mA) 5.4 33.0 5.3 32.5 5.2 32.0 Icc, -30 5.1 31.5 Icc, 25 Icc, 85 5.0 -10.0 31.0 -8.0 -6.0 -4.0 -2.0 0.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 LO (dBm) VCC (V) Cellular LO Buffer Output, LOIN @ -5 dBm -10.00 (T1 Insertion Loss Not Taken Into Consideration) -10.50 Cellular LO Buffer Output (dBm) -11.00 -11.50 -12.00 -12.50 Isolation, -30 Isolation, 25 Isolation, 85 -13.50 2.75 -13.00 2.85 2.95 3.05 3.15 3.25 3.35 VCC (V) 8-50 Rev A4 010828 Preliminary LNA PCS Band (Low Gain Mode) -4.0 27.0 RF2492 LNA PCS Band (Low Gain Mode) -5.0 26.0 -6.0 IIP3 (dBm) 25.0 Gain, -30 Gain, 25 Gain, 85 -7.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 24.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 Gain (dB) IIP3, -30 IIP3, 25 IIP3, 85 VCC (V) VCC (V) LNA PCS Band (High Gain/Nominal IP Mode) 16.0 3.6 3.4 15.5 3.2 3.0 LNA PCS Band (High Gain/Nominal IP Mode) 8 FRONT-ENDS IIP3, -30 IIP3, 25 IIP3, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 IIP3 (dBm) Gain, -30 Gain, 25 Gain, 85 2.7 2.8 2.9 3.0 3.1 3.2 3.3 Gain (dB) 15.0 2.8 2.6 2.4 2.2 2.0 14.5 14.0 13.5 1.8 VCC (V) VCC (V) Rev A4 010828 8-51 RF2492 LNA PCS Band (High Gain/Max IP Mode) 10.5 1.9 1.8 1.7 10.0 1.6 Preliminary LNA PCS Band (High Gain/Max IP Mode) Noise Figure (dB) 1.5 1.4 1.3 1.2 1.1 1.0 NF, -30 NF, 25 IIP3 (dBm) 9.5 9.0 IIP3, -30 IIP3, 25 IIP3, 85 8.5 2.7 2.8 2.9 3.0 3.1 3.2 3.3 NF, 85 0.9 0.8 0.7 2.7 2.8 2.9 3.0 3.1 3.2 3.3 VCC (V) VCC (V) LNA PCS Band (High Gain/Nominal IP) 4.45 4.40 6.35 LNA PCS Band (High Gain Mode/Max IP Mode) 6.30 8 FRONT-ENDS ICC (mA) 4.35 4.30 6.25 6.20 4.25 4.20 4.15 4.10 Icc, -30 4.05 4.00 2.70 Icc, 25 Icc, 85 2.80 2.90 3.00 3.10 3.20 3.30 5.95 2.70 2.80 2.90 3.00 3.10 3.20 3.30 6.00 6.05 ICC (mA) 6.15 Icc, -30 Icc, 25 6.10 Icc, 85 VCC (V) VCC (V) LNA PCS Band (High Gain/Nominal IP Mode) 2.0 16.5 LNA PCS Band (High Gain/Max IP Mode) 1.8 16.0 1.6 Noise Figure (dB) 1.4 1.2 NF, -30 1.0 NF, 25 NF, 85 Gain (dB) 15.5 15.0 14.5 0.8 Gain, -30 Gain, 25 Gain, 85 14.0 2.7 2.8 2.9 3.0 3.1 3.2 3.3 2.7 2.8 2.9 3.0 3.1 3.2 3.3 0.6 VCC (V) VCC (V) 8-52 Rev A4 010828 Preliminary RF2492 PCS Band, Mixer IF1, Low Gain Mode, LO @ -5 dBm 18.50 15.00 PCS Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 18.00 14.50 17.50 8 14.00 Noise Figure (dB) Gain (dB) 17.00 13.50 16.50 NF, -30 16.00 NF, 25 NF, 85 15.50 13.00 12.50 Gain, -30 Gain, 25 Gain, 85 15.00 2.75 2.85 2.95 3.05 3.15 3.25 3.35 12.00 2.75 2.85 2.95 3.05 3.15 3.25 3.35 VCC (V) VCC (V) Rev A4 010828 8-53 FRONT-ENDS RF2492 PCS Band, Mixer IF1, High Gain Mode PCS Band, Mixer IF1, Low Mode, LO @ -5 dBm 5.00 57.16 57.14 57.12 4.50 57.10 14.5 21.00 22.00 15.0 Preliminary PCS Band, Mixer IF1, High Gain Mode, PCS Low Gain Mode, LO @ -5 dBm VCC @ 2.75 V LO to IF Isolation (dB) Gain (dB) Isolation, 25 Isolation, 85 57.06 57.04 3.50 57.02 57.00 3.00 56.98 56.96 2.50 56.94 2.75 2.75 Gain (dBm) IIP3 (dBm) 57.08 4.00 Isolation, -30 14.0 20.00 13.5 19.00 13.0 Gain, -30 Gain, 25 Gain, 85 18.00 12.5 Gain, -30 Gain, 25 Gain, 85 IIP3, -30 IIP3, 25 IIP3, 85 2.85 -8.0 2.95 -6.0 3.05 -4.0 3.15 3.25 -2.0 3.35 0.0 2.85 2.85 2.95 2.95 3.05 3.05 3.15 3.15 3.25 3.35 17.00 12.0 2.75 -10.0 VCC (V) VCC (V) LO CC (V) V (dBm) PCS Band, Mixer IF1, High Gain Mode, 7.9 7.8 PCS Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 37.0 36.5 36.0 35.5 VCC = 2.75 V 8 FRONT-ENDS IIP3 (dBm) 7.7 7.6 7.5 ICC (mA) 35.0 34.5 34.0 7.4 7.3 7.2 7.1 7.0 6.9 -10.0 IIP3, -30 IIP3, 25 IIP3, 85 -8.0 -6.0 -4.0 -2.0 0.0 33.5 Icc, -30 33.0 32.5 2.7 2.8 2.9 3.0 3.1 3.2 3.3 Icc, 25 Icc, 85 LO (dBm) VCC (V) PCS Band, Mixer IF1, HighIN @ -5 dBm PCS LO Buffer Output, LO Gain Mode, 11.00 -10.00 PCS Band, Mixer IF1, High Gain Mode, LO @ -5 dBm 10.00 (T2 Insertion LossLO @ -5 dBm Consideration) Not Taken Into -10.50 Cellular LO Buffer Output (dBm) IIP3 (dBm) 10.00 -11.00 -11.50 9.00 -12.00 8.00 -12.50 Noise Figure (dB) 9.00 8.00 -13.00 7.00 -13.50 Isolation, -30 IIP3, -30 Isolation, 25 IIP3, 25 Isolation, 85 IIP3, 85 2.85 2.85 2.95 2.95 3.05 3.05 3.15 3.15 3.25 3.35 7.00 2.75 2.80 2.85 2.90 NF, -30 NF, 25 NF, 85 -14.00 6.00 2.75 2.75 2.95 3.00 VCC (V) VCC (V) VCC (V) 8-54 Rev A4 010828 |
Price & Availability of RF2492 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |